FIREFOX:
Locate the IP address of your printer (shown on the startup page or configuration page)
Open Firefox;
MAC OSX - Go to the File menu and select Preferences
WINDOWS - Go to the Tools menu and select Options
Click the Advanced (gear icon) across the top of the window
Select the Network tab and click the Settings button
Type the IP address of the printer into the field labeled "No proxy for:"
Click ok, restart FireFox and type the printer IP address to access the internal web page.
SAFARI (Mac OS)
Locate the IP address of your printer (shown on the startup page or configuration page)
Open Safari; Go to the File menu and select Preferences
Click the Advanced (gear icon) across the top of the window
Locate Proxies and select Change Settings; this will open the Network preferences
Type the IP address of the printer into the field labeled "Bypass proxy settings for these Hosts & Domains:"
Click Apply Now, restart Safari and type the printer IP address to access the internal web page.
INTERNET EXPLORER (Windows)
Locate the IP address of your printer (shown on the startup page or configuration page)
Open Internet Explorer; Go to the Tools menu and select Internet Options
Select the Connections tab and click the LAN Settings button
Under the Proxy Settings area; click the Advanced button
Type the IP address of the printer into the field labeled "Exceptions"
Click ok, restart Internet Explorer and type the printer IP address to access the internal web page.
This is caused when arcing occurs across the surface of the toner drum. To correct this, pull the toner cartridge from the printer and check the metal contacts on the left side of the printer. Make sure that they are not laying flat. On the right side, following the guide for the toner you will notice another contact, which is the ground. Make sure that it is not pushed in to where it does not make contact with the toner. Gently pull this out to ensure contact.
The Bias Transfer Roller (BTR) behind the toner drum is black and spongy. It has two beige handles. Make sure that you can push this down and it springs back into place. Check both ends to ensure each springs back. You may need to take this roller out and clean it. Make sure that you get it seated properly. Also, try replacing the toner cartridge itself. On occasion, the sides of the toner cartridge not making good contact can also cause the problem. If the problem is still occurring, the EP setting may need adjustment. Please contact Tech Support if you are not familiar with performing this adjustment.
The problem is either a physical connection or configuration issue. First, verify that the printer's parameters are properly configured. This includes a valid IP address, the same subnet mask as is used on the PC, and in some cases, a valid default gateway. If these values are entered manually instead of through DHCP then the DHCP setting on the printer must be turned off in order for the settings to apply. Make sure the printer has been rebooted after changing IP parameters. Once you are certain that the printer has been properly configured, try PINGing the printer from the PC. If the PING is successful then IP communication has been established and an LPR port needs to be configured to allow printing to an IP address. If the PING is not successful, and you are certain that the printer's IP parameters are properly configured, then you must check the physical connection. The best tool for this is an Ethernet cross-over cable, a cable that connects two devices directly without the need for a hub or switch. Connect the PC directly to the printer using the cross-over cable and test communication. If no communication can be established using the cable or the main network, and the PC can communicate with other devices via Ethernet, then the printer's Ethernet interface has failed. Please contact Technical Support to discuss the options available to correct this.
DHCP is standard on Series 4/5 and available for Series 3 using ROM v 4.01-4 or higher.
Adjust the density from your web browser or on the front panel under SETUP: MEDIA for the media type on which you are printing. You can also go to your printer's browser and adjust the density. The toner cartridge also may be getting close to end of life; if so, replacing the toner cartridge should help to resolve the issue.
The printer is formatting the page for the wrong size media. The paper guides in the tray are probably out of place. Adjust the paper guides in the tray and make sure that the pointers on the guides are in the correct position. To test, press ONLINE, TEST, ONLINE to print out a startup page.
Engine tolerances for this printer are plus or minus 2 mm. If your line lengths are off this much or less, you can try to correct the problem using XANTÉ's patented More X-ACT calibration. This technology corrects for inconsistent line lengths and skew and should allow you to get your line lengths under control. With X-ACT, you should be able to get these line lengths within plus or minus .5 mm for every 12 inches of media.
Skew can be caused by the way the media is fed through the printer. Check to see if the skew occurs from all trays or only one tray. If it only occurs from a single tray, then observe the pickup rollers and see if they are causing the media to be fed through the printer at an angle. Also, make sure that the media is aligned properly when loaded in the tray. If the problem occurs from all trays, perform X-ACT calibration which corrects for skew.
DO NOT use media that is unusually thick, thin, wrinkled, torn, curled, creased, wet, damp, or damaged. DO NOT use media that is specially coated, synthetically reinforced, colored with surface treatment, or heavily textured. DO NOT use media that has metal clasps, strings, staples, cutouts, perforations, or windows. ONLY USE media that has been rated "laser safe" by the manufacturer.
E:FUSER is displayed when the temperature sensor inside the fuser does not read the correct temperature (too high or too low).
E:SCANNER is displayed when the laser unit is not level, a bad connection is detected by the sensor or the scanner motor has stopped moving.
TCP/IP, Ethertalk.
You either do not have INSTALLED RAM configured correctly under the INSTALLED OPTIONS or you do not have enough physical memory to print at that resolution. The physical memory is displayed on your Startup Page.
DHCP may not be setup to assign addresses correctly which will reassign the IP address each time you restart your printer. We recommend you set a static IP address to avoid the problem.
LOW PAPER is displayed when there are fewer than 100 sheets (using 75 gsm) in the cassette tray.
Verify that the INSTALLED RAM and RESOLUTION under the INSTALLED OPTIONS matches the physical configuration displayed on the Startup Page.